★ GUIDES · EVERYDAY · CARS · DRIVING
How to Calculate Your Reaction Time in Four Easy Steps
202 ms is what a 20 cm ruler drop means. Work through the four steps below and you will land on the same figures as the worked example: 202 ms, rated Good, and 17.8 feet at 60 mph. If you would rather skip the arithmetic, the Reaction Time Calculator: Test Your Reflexes in ms runs the same steps for you.
Step 1: Drop the ruler and measure the fall
Hold a ruler at the top with the zero end down, just above a friend’s open hand, and drop it without warning. Your friend catches it as fast as they can, and you measure from their fingertips to where they caught it: that distance is the fall, in centimetres. A 20 cm catch is a typical result, a 10 cm catch is quick, and a 40 cm catch is slow. Take the best of three tries, and measure honestly — a centimetre either way moves the answer by about 5 ms, so a sloppy measurement is a wrong reaction time. Write the figure down in centimetres, because every step after it uses it.
Step 2: Convert the centimetres to metres
The formula works in metres, so divide the centimetres by 100: 20 cm is 0.20 m, 10 cm is 0.10 m, and 40 cm is 0.40 m. This is the step people skip, and skipping it breaks everything: using 20 instead of 0.20 gives a reaction time of 2.02 seconds instead of 202 ms, ten times too slow. Keep two decimal places — 0.20, not 0.2 — so the doubling in the next step stays exact.
Step 3: Double it, divide by gravity, and take the square root
The formula is t = √(2d ÷ g), where d is the fall in metres and g is 9.81, the acceleration of gravity. Double the distance and divide by 9.81: 2 × 0.20 ÷ 9.81 is 0.0408. Then take the square root: √0.0408 is 0.202 seconds. Multiply by 1,000 to get milliseconds: 0.202 × 1,000 is 202 ms. A 10 cm fall works out to 0.143 seconds, or 143 ms, and a 40 cm fall to 0.286 seconds, or 286 ms. Any scientific calculator has a square-root key; on a phone, search for the square root of the number.
Step 4: Rate it, and work out the driving distance
Read the rating from the bands: under 200 ms is Excellent, 200–249 ms is Good, 250–299 ms is Average, 300–399 ms is Slow, and 400 ms or more is Very slow. A 202 ms catch is Good. Then work out what it means on the road: multiply your speed in feet per second by the reaction time in seconds. At 60 mph the car covers 88 feet a second, so 88 × 0.202 is 17.8 feet — the distance travelled before your foot even starts moving. At 30 mph it is 44 × 0.202 = 8.9 feet, and at 70 mph it is 102.7 × 0.202 = 20.7 feet. The grip that stops the car depends on pressure, so the Tire Pressure Calculator: PSI for Cold, Hot & Winter Days is worth a monthly check. Check the answer against the Reaction Time Calculator: Test Your Reflexes in ms, which runs the same four steps from any fall and speed.
Worked example
The defaults, step by step: the ruler falls 20 cm and the car is doing 60 mph. Step one: the fall is 20 cm. Step two: convert to metres. 20 ÷ 100 is 0.20 m. Step three: the formula. 2 × 0.20 ÷ 9.81 is 0.0408, and the square root is 0.202 seconds, or 202 ms. Step four: rate it and work out the driving distance. 202 ms is Good, and 88 × 0.202 is 17.8 feet at 60 mph. A second example, quick hands: a 10 cm fall is 0.10 m, 2 × 0.10 ÷ 9.81 is 0.0204, the square root is 0.1428 seconds, or 143 ms — Excellent — and 88 × 0.1428 is 12.6 feet. A third, tired: a 40 cm fall is 0.40 m, 2 × 0.40 ÷ 9.81 is 0.0815, the square root is 0.2856 seconds, or 286 ms — Average — and 88 × 0.2856 is 25.1 feet. The Reaction Time Calculator: Test Your Reflexes in ms reproduces every one of these figures from any fall and speed, and the Braking Distance Calculator: Stopping Distance by Speed works out the full stop that follows.
Three mistakes that break the total
First, measuring in centimetres and using the number as metres: 20 cm is 0.20 m, not 20 m, and using 20 gives 2.02 seconds instead of 202 ms — ten times too slow. Second, measuring from the wrong point: the fall is measured from the fingertips to where they caught the ruler, not from the top of the ruler or the bottom of the hand, and a centimetre of error moves the answer by about 5 ms. Third, testing once while tired or distracted and taking it as your figure: reaction time varies with rest and attention, so test when rested and take the best of three tries — a single slow catch says more about the morning than about you. So convert to metres, measure from the fingertips, and take the best of three.
Frequently asked questions
How do you calculate reaction time?
Measure the ruler fall in centimetres, convert to metres, then use t = √(2d ÷ 9.81): a 20 cm fall is 0.20 m, 2 × 0.20 ÷ 9.81 is 0.0408, and the square root is 0.202 seconds, or 202 ms.
What is a good reaction time?
Under 200 ms is Excellent, 200–249 ms is Good, 250–299 ms is Average, 300–399 ms is Slow, and 400 ms or more is Very slow. A 20 cm ruler catch is 202 ms, Good; a 10 cm catch is 143 ms, Excellent.
How far does a car travel in 202 ms?
At 60 mph the car covers 88 feet a second, so in 202 ms it covers 17.8 feet. At 30 mph it covers 8.9 feet in the same time, and at 70 mph it covers 20.7 feet.
What is the formula for reaction time?
Reaction time = √(2 × distance ÷ 9.81), with the distance in metres and 9.81 the acceleration of gravity. At the defaults that is √(2 × 0.20 ÷ 9.81) = 0.202 seconds, or 202 ms. Car distance is speed × reaction time.
Is the ruler-drop test accurate?
It is accurate for simple reaction time: the maths is exact, and a centimetre of measurement error moves the answer by about 5 ms. It is faster than real driving reaction, though — driving adds noticing, deciding, and moving your foot, and the standard driving allowance is 1.5 seconds.
How can I improve my reaction time?
Rest, practice, and attention: a rested driver catches the ruler sooner than a tired one, and the test itself is practice. The biggest gain on the road is not faster hands but a longer following distance — 17.8 feet at 60 mph is already more than a car length.