1754
Juniper mulch chart
Put your juniper mulch area, depth and waste in: 1350 sq ft at 3-inch depth with 10% waste needs 1,485.00 sq ft — 13.75 cubic yards exact, order 14.
★ CONSTRUCTION · REFERENCE TABLE #489 · JUNIPER MULCH
Juniper Mulch Chart: 1350 Sq Ft at 3 Inches, Order 14 Yards
On the defaults — 1350 square feet at a 3-inch depth with 10% waste — juniper mulch needs 1,485.00 square feet of coverage, which is 13.75 cubic yards exact, so order 14 cubic yards. This is reference table #489 — the juniper version of the mulch chart, with a calculator on top and a 16-row lookup table below, following the elm-mulch-chart page, the poplar-mulch-chart page, and the aspen-mulch-chart page.
What does 13.75 cubic yards of juniper mulch mean?
It means 1,485.00 square feet of ground — the 1350 square feet you measured plus 10% waste — covered 3 inches deep in juniper mulch. One cubic yard covers 324 square feet at 1 inch, so at 3 inches each yard covers 108.0 square feet, and 1,485.00 divided by 108.0 is 13.75 yards. You cannot order 0.75 of a yard from a bulk supplier in practice, so the order rounds up to 14: the extra 0.25 of a yard is topping-up, not waste, because chips settle into the gaps between pieces as they bed in.
Output · formula · meaning
| Output | Formula | What it means |
|---|---|---|
| Needed area | area × (1 + waste ÷ 100) | 1,485.00 sq ft — 1350 × 1.10. |
| Exact cubic yards | needed area × depth ÷ 324 | 13.75 — 1,485.00 × 3 ÷ 324. |
| Order | exact cubic yards rounded up | 14 cubic yards — the next whole yard above 13.75. |
| Coverage per yard | 324 ÷ depth | 108.0 sq ft per yard at 3 inches. |
| Needed area at 0% waste | area × 1.00 | 1,350.00 sq ft — no allowance added. |
| Area behind a target exact figure | target × 324 ÷ depth ÷ (1 + waste ÷ 100) | 1350 sq ft — 13.75 × 324 ÷ 3 ÷ 1.10. |
| Depth behind a target exact figure | target × 324 ÷ needed area | 3 inches — 13.75 × 324 ÷ 1,485.00. |
| Waste behind a target exact figure | (target × 324 ÷ depth ÷ area − 1) × 100 | 10% — (13.75 × 324 ÷ 3 ÷ 1350 − 1) × 100. |
Three things to check before you trust the number
First, measure only the beds the juniper will actually cover: paths, lawn and bare soil inside your measurement inflate the order by their full area times depth. Second, pick the depth for juniper, not for bark: juniper chips are reddish-brown, aromatic and slow to break down, and 3 inches gives a full, even cover that suppresses weeds without smothering shallow-rooted plants, while copying a deep bark depth overstates the order. Third, keep the waste allowance honest on slopes and open ground: juniper chips are moderately dense, so wind moves them less on open ground, but a steep bank still sheds chips downhill before they bed in.
Worked example
Area 1350 square feet, depth 3 inches, waste 10%. Needed area: 1350 × 1.10 = 1,485.00 square feet. Exact yards: 1,485.00 × 3 ÷ 324 = 13.75 cubic yards. Order: 14 cubic yards. At 4 inches instead, the same area needs 18.33 yards exact — order 19 — because one inch more across 1,485.00 square feet is 1,485.00 ÷ 324 = 4.58 more yards. Depth is the lever that moves this chart fastest.
Juniper mulch lookup table
Every row below is the same formula at 10% waste: needed area is area × 1.10, exact cubic yards are needed area × depth ÷ 324, and the order is the exact figure rounded up. Rows vary in both area and depth, so a shallow small bed and a deep large one can both be read off directly. Find your row, or use the calculator above for any size the table does not list.
| Area (sq ft) | Depth (inches) | Needed area (sq ft) | Exact cubic yards | Order |
|---|---|---|---|---|
| 300 | 2 | 330.00 | 2.04 | 3 cubic yards |
| 500 | 3 | 550.00 | 5.09 | 6 cubic yards |
| 750 | 2 | 825.00 | 5.09 | 6 cubic yards |
| 400 | 4 | 440.00 | 5.43 | 6 cubic yards |
| 950 | 3 | 1045.00 | 9.68 | 10 cubic yards |
| 600 | 4 | 660.00 | 8.15 | 9 cubic yards |
| 1350 | 3 | 1485.00 | 13.75 | 14 cubic yards |
| 850 | 2 | 935.00 | 5.77 | 6 cubic yards |
| 1400 | 3 | 1540.00 | 14.26 | 15 cubic yards |
| 1050 | 4 | 1155.00 | 14.26 | 15 cubic yards |
| 650 | 5 | 715.00 | 11.03 | 12 cubic yards |
| 1100 | 2 | 1210.00 | 7.47 | 8 cubic yards |
| 1550 | 3 | 1705.00 | 15.79 | 16 cubic yards |
| 900 | 4 | 990.00 | 12.22 | 13 cubic yards |
| 1350 | 4 | 1485.00 | 18.33 | 19 cubic yards |
| 1750 | 2 | 1925.00 | 11.88 | 12 cubic yards |
Every branch, checked
At 0% waste, 1350 square feet at 3 inches needs 12.50 yards exact — order 13. At 2 inches with 10% waste, the same area needs 9.17 yards exact — order 10. At 1500 square feet with 3 inches and 10% waste, the order is 15.28 yards exact — order 16. At 1100 square feet with 3 inches and 10% waste, the order is 11.20 yards exact — order 12. Each branch changes exactly one input, so the difference from 13.75 isolates that input.
The reverses, worked backwards
The area behind 13.75 yards is 1350 square feet: at 1250 square feet the figures are 12.73 yards exact — order 13, and at 1450 square feet they are 14.77 yards exact — order 15. The depth behind 13.75 yards is 3 inches: at 2 inches the figures are 9.17 yards exact — order 10, and at 4 inches they are 18.33 yards exact — order 19. The waste behind 13.75 yards is 10%: at 5% the figures are 13.13 yards exact — order 14, and at 15% they are 14.38 yards exact — order 15 — waste moves the exact figure here, and the order moves with it at the upper neighbor only.
What the defaults assume
The defaults assume a flat 1350 square feet, a uniform 3-inch layer, and a 10% waste allowance. Real beds are not uniform: edges thin out, the ground underneath undulates, and chips poured thick in the middle and thin at the edges average out only roughly. Zero square feet is the honest edge: 0.00 yards exact, order 0. Negative area, zero depth and negative waste are rejected — none of them describes a bed you can mulch. Re-measure after the first barrow loads if the pile looks wrong: catching a measurement error early beats ordering a second delivery.
Who uses this
A home gardener mulching beds with juniper for a warm, reddish finish: the chart prices the order before the delivery truck arrives, and the lookup table answers the common bed sizes without a calculator. A landscaper quoting an juniper job: the waste allowance is the margin between a short load and a second delivery charge. A groundskeeper topping up paths and play areas: juniper is firm underfoot and slow to break down, and the depth choice sets both the order and the refresh cycle. A garden-centre clerk answering “how much do I need”: the area, depth and waste inputs turn a rough bed size into a whole-yard order on the spot.
Accuracy & limitations
The arithmetic is exact for the inputs entered; the judgement is in the inputs. An area that includes paths, a depth guessed rather than measured, or a waste allowance that ignores slope will each move the answer by exactly the amount of the error. The model does not include delivery minimums, bulk-bag sizes, compaction after rain, or the slower breakdown of juniper against bark — re-check the depth after the first season, and re-measure beds that were only paced out. This page is a calculation tool, not landscaping advice.
Cite this calculator
Juniper mulch 1350 sq ft at 3-inch depth with 10% waste needs 1,485.00 sq ft — 13.75 cubic yards exact, order 14. Calculator plus 16-row lookup table, free. Source: Bright Side Kit, https://brightoolbox.com/juniper-mulch-chart/, accessed 30 October 2026 (2026-10-30).
Frequently asked questions
How many cubic yards of juniper mulch do I need?
Area times depth divided by 324, plus waste: 1350 square feet at 3 inches with 10% waste is 1,485.00 square feet needed, 13.75 yards exact, order 14. Use the calculator for any size the lookup table does not list.
Why order 14 yards when the exact figure is 13.75?
Because bulk mulch is sold by the whole yard, and the 0.25 extra is topping-up that settles into gaps as the chips bed in. Ordering 13 would leave the last beds thin once the chips settle.
Is 3 inches the right depth for juniper?
For most beds, yes: deep enough to suppress weeds and hold moisture, shallow enough not to smother shallow roots. Use 2 inches for a light refresh over existing mulch and 4 inches only where weed pressure is heavy.
What does the 10% waste allowance cover?
Settling, spreading loss and uneven ground. Juniper chips are moderately dense, so wind moves them less than light chips; use more than 10% on steep or open ground and less on flat, sheltered beds.
How does juniper differ from bark mulch in this chart?
Only in how fast it breaks down and how dense it is: the volume formula is the same, but juniper settles slower, so a 3-inch juniper layer holds its depth longer than a 3-inch bark layer and needs topping up later.
Can I use the lookup table instead of the calculator?
Yes, for the sizes listed: find your area and depth row and read the order across. For any other size, the calculator above applies the same formula with your exact figures.